This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
tymcom-x-tape [2018/04/10 08:30] jms [Putting TITO.SAV on disk using FILDDT] |
tymcom-x-tape [2018/04/24 07:59] (current) jms [Putting TITO.SAV on disk using FILDDT] |
||
---|---|---|---|
Line 189: | Line 189: | ||
15. Boot TYMCOM-X in production mode. Due to Y2K8 problem, must use date from 28 years ago. | 15. Boot TYMCOM-X in production mode. Due to Y2K8 problem, must use date from 28 years ago. | ||
- | (Hit Enter twice to get logged in, then '' | + | (Hit Enter twice r Control-Z L to get logged in, then '' |
| | ||
Line 264: | Line 264: | ||
At this point, '' | At this point, '' | ||
- | Current project: | + | ===== Copying MON14.SAV to the disk ===== |
+ | |||
+ | Since we don't have KERMIT or other file transfer program on TYMCOM-X, do it with '' | ||
+ | |||
+ | On TOPS-10, start a Receive ASCII operation and display the whole monitor in octal. | ||
+ | |||
+ | .r filddt | ||
+ | File: mon14.sav/ | ||
+ | $$a $$h 0$n | ||
+ | 0/ | ||
+ | 1/ | ||
+ | ... | ||
+ | 245643/ | ||
+ | 245644/ | ||
+ | |||
+ | Edit the saved text to remove the first lines, and change "/" | ||
+ | |||
+ | Set the terminal emulator to delay 17 milliseconds between characters for the Send ASCII operation. | ||
+ | |||
+ | !run (mpl)filddt | ||
+ | File: (sys)system.sav/ | ||
+ | $$a $$h | ||
+ | 0/ | ||
+ | 1/ | ||
+ | ... | ||
+ | 245643/ | ||
+ | 245644/ | ||
+ | ^Z | ||
+ | |||
+ | Exit the TYMCOM-X simh job and start fresh (to get the implied zeroing of memory). | ||
+ | |||
+ | ^E | ||
+ | sim> | ||
+ | Linux% ./pdp10 x14-prod.ini | ||
+ | PDP-10 simulator V4.0-0 Current | ||
+ | BOOTS: | ||
+ | |||
+ | LOADING (SYS)SYSTEM.SAV | ||
+ | X14, hardware *B*, KS-4257, base 6760, X14-P035/ | ||
+ | |||
+ | Highest memory address is 3,,777777 | ||
+ | |||
+ | Checking all units on disk controller - reading UNIT ID from HOME pages. | ||
+ | | ||
+ | | ||
+ | |||
+ | 1024K of memory online. | ||
+ | X14, hardware *B*, KS-4257, base 6760, X14-P035/ | ||
+ | |||
+ | End of ONCE; starting null job | ||
+ | INITIA starting DSKCLN on TTY0 | ||
+ | |||
+ | Hi there! | ||
+ | proj code: | ||
+ | |||
+ | date not set, type date as mm-dd-yyyy 04-12-1990 | ||
+ | type time as hh:mm 15:53 | ||
+ | |||
+ | .systat | ||
+ | SYSTEM SHUT | ||
+ | |||
+ | TYMSHARE X14-P035/ | ||
+ | Null time = 36:13, Idle = 100% (Idle time per MIN. = 100%) | ||
+ | 2 jobs in use out of 31. 1 detached | ||
+ | |||
+ | JOB TYMNET | ||
+ | | ||
+ | | ||
+ | + means TYMSHARE inhouse user | ||
+ | |||
+ | Users=2 Det=1 [1,1], Queues: RUN=1 DIO=0 TIO=1 IO=0 SPC=0 | ||
+ | 2046 Physical pages available (MONITOR = 282P, User Area = 1764P) | ||
+ | Virt. memory used (TPU/TPA): 48/1764 = 3% | ||
+ | |||
+ | At this point, the systems programmer is expected to use the '' | ||
+ | |||
+ | Use DDT to get the address of JBTLIC (GETTAB table for job license). | ||
+ | |||
+ | ^E | ||
+ | sim> | ||
+ | sim> | ||
+ | sim>go | ||
+ | !pjob | ||
+ | Frame 2 TTY10 OPER[1,21] at X14 | ||
+ | |||
+ | !r ddt | ||
+ | DDT | ||
+ | dskclr 2,$x | ||
+ | DDT | ||
+ | ^C | ||
+ | |||
+ | Use '' | ||
+ | |||
+ | Success! | ||
==== Other pages ==== | ==== Other pages ==== | ||
[[tymcom-x|Overview]] page, [[tymcom-x-simh|SIMH Setup]] page, [[tymcom-x-startup|TYMCOM-X Startup]] page, [[tymcom-x-tape|TITO on disk]] page, [[tymcom-x-status|Status]] page. | [[tymcom-x|Overview]] page, [[tymcom-x-simh|SIMH Setup]] page, [[tymcom-x-startup|TYMCOM-X Startup]] page, [[tymcom-x-tape|TITO on disk]] page, [[tymcom-x-status|Status]] page. | ||